Compliance With Following Standards: Compliance Standards : IS : 2514 For compaction of concrete cube cylinders. The table deck size has stops along its edges to prevent moulds from walking off the table during operation. The variable pitch pulley arrangement permits the frequency to be varied steplessly between maximum of 3600 vibrations down to 2600 vibrations per minute. A speed regulation handle is provided for increasing or decreasing the frequency. The vibrator is mounted on cushioned steel vibrating deck. A switch is provided for starting the motor. Operation on 440 V, three phase, A.C. supply. Also available in Table size 60x60, 75x75, 100x100, 120x120, 120x150, 200x100cm Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Designed for mixing small quantities of concrete used in preparation of concrete cubes for testing in Laboratories. The purpose of the mixer is to smear mechanically the aggregate surface with cement paste uniformly and produce a mix of uniform consistency. This in turn gives consistent quality of cube specimens when casted in the moulds. Also avaible in 60 Litres/80 Litres/100 Litres Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Application: Pull out anchor tester, also known as (anchor rod tension meter). Applicable to testing various anchor rods, anchor cables, steel bars, planting bars, expansion bolts, chemical anchor bolts, railway spikes, and various kinds of anchors. It can also be used for on‐site pull‐out resistance testing of glass curtain walls. It is a necessary testing instrument for each (quality inspection unit, reinforcement unit, supervision unit, university, coal mine, etc.) Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IP 45, IS 1212, ASTM D6-90, AASHTO T-47 Purpose: The loss in bituminous material when heated is called loss on heating of bituminous material. This test is done to determine the amount of loss of bitumen by certain heating and to determine the amount of water mixed in the bituminous material. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D 88 / IS 3117 / IS 8887 The apparatus consists of stainless steel bath with oil cup which is centrally placed in a water bath. The bath has a lid which contains a water cooling tube, two handles with two stirring blades, thermometer socket and a straight heater. Stirring is done by turntable arrangement. A thermometer can also be inserted into the cup cover. Two jets one universal and one furol can be screwed to the cup by a handle (without strainer, withdrawal tube and glass wares) To work on 220V AC single phase. Temperature control by separate energy regulator. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: EN 196-6, ASTM C204, BS 4550 This test method concerns the determination of the particle size of Portland cement, limes and similar powders using the Blaine air permeability apparatus. The measure of fineness is expressed in terms of the specific surface area (the total particle surface area) in square centimeters per gram or square meters per kilogram Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: ASTM C230, ASTM C1437 Also available in M.S. Steel Top. The flow table consists of a brass table top 250 ± 2.5 mm dia mounted on a rigid stand. The table top is reinforced with equally disposed ribs and allowed to drop through 12 mm by a ground and hardened cam, Complete with mould - 100 mm base dia, 70 mm top dia and 50 mm high. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: IS 5512 Also available in M.S. Steel Top. Flow table consist of a brass table top 250 ± 2.5 mm dia mounted on a rigid stand. The table top is reinforced with equally disposed ribs and allowed to drop through 12 mm by a ground and hardened cam, Complete with mould- 100 mm base dia, 70 mm top dia and 50 mm high. The cam shaft is rotated at the rate of 100 RPM by an electric motor. Suitable for operation on 230 Volts 50 cycles. Single Phase, A.C.Supply. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Photometric test Apparatus for quick determination of SO3 in cement. The Model is provided with double light intensity meter, as such useful where the % of SO3 is desired to be known with higher accuracy. The Model is of export quality & provided with constant voltage Transformer built in. Beside this the component used in is of the highest quality available in market. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following International Standards: IS : 9013 Accelerated Curing Tank having capacity to accommodate 3 Nos. concrete cube moulds of 15 cm with a facility for accelerated curing by boiling water method up to temperature range : 100 ± 2 °C as per IS standard IS : 9013. Also it will have capacity for curing by warm water method at temperature 55 ± 2 °C. Also available in various models. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: EN 1427 | ASTM D36 | AASHTO T53 | IP 58 | IS 1205 Availabe in various models such as : 1) Programmable Magnetic Stirrer Cum Heater, 2) A.C. Motorized Stirrer with Electrical Heating, 3) D.C. Motorized Stirrer with Electrical Heating , 4) Fully Automatic Operation and 5) Hand Operated - For Two Test Further details available on our website. Note : Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following International Standards: IS:516, BS:1881 and ASTM C78 Automatic Test Execution: Once the machine has been switched on, the specimen positioned and centered, the only required operations are: Set test parameters including load rate: Press the start button The machine automatically: starts the rapid approach; switches to the test speed once the specimen comes into contact with the upper platen; automatically stops the motor upon specimen failure Save the test including data results . The test execution conforming to Standards can be easily proved. Working on 240V, 50 60Hz, single phase. Dual stage pump assuring fast piston approach and precise test execution Test execution conforming to EN 12390-5, ASTM C78, AASHTO T22 Controllable pace rate from 0.03 KN/Sec to 10 KN/Sec. Auto stop after completion of each test. Soft platen to specimen contact and smooth load rate control from the very beginning of the ramp Servo motor driven machine Auto calculation of the flexural strength after the failure of the sample. Calculation is done after failure of the sample by sending the distance of the nearest roller from the crack. Frame: High stiffness welded frame tested for stability. Heavy duty spherical seat, allowing initial free alignment at the initial contact with the specimen and automatic jamming up to the end of test. Piston travel limit switch (Extra cost) Emergency stop button Servo motor driven machine Gives live online graph on the 7" touch screen User friendly large graphical display Saves 50 results in the 7" touch screen Inbuilt USB drive to save the data. Salient fetchers of data manager PC software (Optional at extra cost.): Two way communication i.e machine operates from computer and from the touch screen controller both (Stat, stop, save data and save graph) Results directly saved in excel file. Graph also saved in excel file. Capable to save customer name, other details of customer, ageing of beam moulds, identification mark of the beam moulds, date and time of testing Capable to print direct report from the computer. Capable to select different test parameters like pace rate, sample size and area from the computer (software) Capable to select different type of tests, like flexural, CTM, aggregate crushing etc. Note: It is recommended to use the machine with 3 KVA servo stabilizer The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: IS:10512-2003 This instrument is used for the determination of the paraffin wax content of bitumen and bituminous binder by distillation. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer. IS:10512-2003 This instrument is used for the determination of the paraffin wax content of bitumen and bituminous binder by distillation. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D445,IP 71,ASTM D446 Also availabe with : 2 Viscometer, 3 Viscometer, 4 Viscometer, 6 Viscometer and 8 Viscometer. Used to determine the viscosity of oils and fuel, above room temperature up to a maximum of 120 °C. Generally used @ 40°C but can also be used at any other temperature between measuring range. Can also be used for other application where full visibility of sample and constant temp. is important for the test. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D 5404 / D5404M - 21, IS 18130 : 2023 Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator. Applications for Recovery of Asphalt Binder from Solution . The solution of bitumen and solvent from a prior extraction is distilled by partially immersing the rotating distillation flask of the rotary evaporator in a heated oil bath. The solution is subjected to a partial vacuum and a flow of nitrogen gas or carbon dioxide gas. These gases provide inert atmosphere to prevent oxidation of the bitumen during the recovery process Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Compliance With Following National / International Standards: The Fraass breaking point method provides a measure of the brittleness of bitumen and bituminous binders at low temperatures. A bituminous binder sample is spread on a thin steel blade to a uniform thickness, this blade is subjected to constant cooling and flexed repeatedly until the binder layer cracks. The temperature at which the first cracking appears is noted as the Fraass point. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D 1559 , ASTM D 6926; AASHTO T245 It is a motor driven mechanical compactor useful for compaction in to 4" dia Marshal moulds. It is fitted with a compaction rammer weighing 4.5 kg. with a free fall of 457 mm. The rammer assembly is provided with a ratchet and pawl arrangement to lift it from the top of the test sample. When the rammer reaches the required height the pawl release the rammer which falls freely on test specimen. The release mechanism is connected by an arm moving up and down which is connected to a reduction gear coupled to the motor through another arm. An automatic blow counter fitted to the compactor is used to set the number of blows. Supplied without Moulds. - Available at extra cost Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following International Standards: EN 12390-4, ASTM C39, AASHTO T22, IS : 14858 (2000) Manufactured as per International design, Plate model for highest mechanical stability, accurate centering of load and excellent repeatability. Fully Automatic pace rate control, auto stop and auto release on failure of test specimen, can be attached with flexural load frame or additional load frame. attachment for Split tensile test, Modulus of Elasticity also available. Please visit YouTube video of the machine by clicking on this link https://youtu.be/9n-Ac_T_18k Note - Price and specifications mentioned here indicative only and are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D 2172, AASHTO T58, AASHTO T164, EN 12697-1 SPECIAL MODEL WITH AC MOTOR AND DRIVE : This model facilitates precise speed control and vibration free smooth operation. Speed variation up to 3600 RPM. Complies with following International Standards - ASTM D 2172, AASHTO T 58, T 164. Electronic weighing Balance, Filter Paper and solvent are available at extra cost. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IS : 1208, ASTM D 113, ASTM D5892, ASTM D6084, AASHTO T51 Ductility is defined as distance in (cms) to which a standard briquette of bitumen can be stretched before the thread breaks. The briquette is stretched at a rate of 50 mm/min ± 2.5 mm/min at a temperature of 27° C ± 0.5° C Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: Oven is designed to determine the the effect of heat & air on asphaltic materials (thin film test).The unit is heavily insulated & has a double glass built in door for view inside temperature is controlled at 163°C ± 1°C. by means of a calibrated PID based DIGITAL TEMP. INDICATOR CONTROLLER. Inside Suspended a 340 mm dia rotating platform having provision to keep 4 Nos. sample containers of 140 mm ID X 10 mm Internal depth, rotated by external motor from 5 to 6 R.P.M. (supplied with cups). Inner chamber made of stainless steel sheet of 304 grade & outer of mild steel sheet ‑ powder coated. To work on 230 volts, AC 50 Hz supply. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IS 1206 (Part II) and (Part III), ASTM D2171, ASTN D2170, EN 12596 As per IS: 1206 (Part II and III).Supplied complete with Viscosity bath with built in Digital stop watch, Vacuum Pump - capable to maintain vacuum of 300 mm/Hg, Indian Make Vacuum Manning Viscometer No.12 and 13, Reverse flow Viscometer No.6, Silicon oil, silicon tubes and calibration certificate for Viscosity bath, certificate of constant for Viscometers. Complete with instruction manual. Detailed Specification as mentioned in technical part mentioned below. Canon USA Make Glass U Tube Viscometer, Mercury Manometer, Digital Vacuum Indicator cum controller etc. are available at extra cost Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: As per IS 1203. As per IS 1203. Basic Model with fine adjustment facility for ease of precise setting.. As per IS 1203. The apparatus consist of a cast aluminum base with an iron stand on which moves an aluminium arm. A 6" dial is fixed on this arm and a brass chromium plated rod slide through the lower portion of the arm. A needle with weights is fitted to this rod. The dial is graduated from 0‑400 in one tenth millimeter sub division. Supplied complete with adjustable needle holder, penetration needle, sample container, transfer dish and weight of 50 gm. Digital stop watch is essential to perform the test at extra cost. Model with Automatic controller and fine adjustment facility also available. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: IP‑49,IS‑1448 This apparatus is used for penetration test on a wide variety of materials such as grease, petroleum, Bitumen, Tar, Wax, Polish, foodstuff, rubber asphalts and Pharmaceutical creams. A depression is made in the sample by a needle of a definite weights which is measured intenths of a millimeter and expressed as penetration number. The apparatus consist of a cast aluminium base with an iron stand on which moves an aluminium arm. A 6" dial is fixed on this arm and a brass chromium plated rod slide through the lower portion of the arm. A needle with weights is fitted to this rod. The dial is graduated from 0‑400 in one tenth millimeter sub division. Supplied complete with adjustable needle holder, penetration needle sample container, transfer dish and weight of 50 gms. Without automatic DIGITAL timer with electrical arrangement. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: ASTM D937, IS 1508, IS 4887, IP 179, ISO 2137 Details The Penetrometer is so designed that it permits the specified cone to drop vertically at least 40 mm and indicates accurately the depth of Penetration to nearest 0.1 mm. The Penetrometer has a platform to accommodate the test sample which can be adjusted horizontally before making the test and a mechanism for releasing the clamp of the loaded cone. The Cone is made of brass with detachable hardened steel tip, constructed to conform to the dimensions and tolerances shown in Fig. 1 of IS : 4887. The total weight of the cone and its movable attachments will be 150.0 ± 0. 1 g. The attachments consist of a rigid shaft having a suitable device at its lower end for engaging the cone. The outer surface is polished to a very smooth finish. Supplied with 1 No. each Cone, sample container and weight. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Compliance With Following National / International Standards: EN 1427 | ASTM D36 | AASHTO T53 | IP 58 | IS 1205. The apparatus consist of a Glass beaker made up of heat resistant glass having internal diameter of 8.5 cm and 12 cm depth (approximately). The heater is controlled by a programmable Digital Auto‑tune PID Temperature Controller Cum Indicator to ensure rise of temperature at 5° C as per the guidelines of ASTM/ISO/AASTHO/IS Standards. Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
Used to determine the strength of the concrete & concrete type hard materials
Salient Features: Fully Automatic operational Design Compact design and rugged construction ensures long service life and facilitates easy transport for field applications. Sturdy cast iron base provides excellent support Digital Alphanumerical LCD touch screen display with keyboard (LCD Make : Schneider Electric) Optoelectronically depth detection & measurement through imported optoelectronic sensor Automatically timed programmable penetration measurements - Preset penetration time at factory (Operator can also enter the user defined penetration interval through LCD touch screen) Motorized placement of penetrator on sample surface Penetrometer arm automatically comes back to its home position at the end of 5 seconds penetration test In-built Facility to tare and reset the measurement results Display resolution of penetration depth in tenths of units (0.01mm) Magnifying lens for adjusting needle tip/cone tip exactly on the sample surface Low voltage Illuminator mounted on flexible arms to assist an operator during testing Built-in spirit level and leveling screws to ensure proper alignment Micrometer differential gearing mechanism for fine movement of head Weight of the Needle/Cone and plunger match the criteria of ASTM and IP requirements. The penetration time is controlled and indicated on Digital LCD display with least count of 0.1 second. The optoelectronic sensor installed within the instrument detects the penetration depth in 10th of millimeter (0.01mm) The penetration value is measured and indicated on digital LCD display Large, removable base accommodates grease worker cups and other ASTM and non-standard sample containers Complete selection of penetrometer cones, needles and accessories for petroleum products testing and for a wide range of other applications (See optional accessories) Supplied complete with Needle/cone, container and applicable weight Weight of 50 Grams - 1 No. Penetration cup of 55mm diameter x 35mm height - 1 No. Penetration cup of 70mm diameter x 45mm height - 1 No. Transfer dish - 1 No. Penetrometer Needle - 1 No. Needle Holder 47.5g ± 0.05g - 1 No.7) Thermometer ASTM 17C (+19 to 27 °C) - 1 No. Specifications: Sample container of 100mm dia x 100mm height - 1 No Transfer dish - 1 No Penetrometer Hollow 90° brass cone, Highly polished stainless steel tip - 2 Nos Supplied complete with following Accessories in case of Bitumen penetration Note - Price will be change as per specification
Compliance With Following National / International Standards: IP 34, ASTM D‑93, IS ‑ 1448 and IS ‑ 1209 This is widely used for determination for closed cup Flash Point of Fuel Oil, cut back asphalts, other viscous material and suspension of solids having a flash point above 49° C (50° C ‑ 360° C). Also available in various models such as : 1) With Energy Regulator 2) With Voltage Stirrer 3) Digital with Motorised Stirrer 4) Semi Automatic with Heating Facility 5) Semi Automatic with Heating and Cooling Facility and 6) Fully Automatic Further details available on our website. Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.
As per ASTM D6926 It consists of three parts: heating pot, stirrer and Lifting mechanism. It consists of three parts: heating pot, stirrer and Lifting mechanism. The temperature of the heating pot can be set arbitrarily from room temperature to 250 ℃, and the temperature can be controlled automatically. The agitator is composed of a mixing head, a motor and a mixing paddle. During operation, the mixing paddle rotates and rotates in the pot to mix the mixture. The mixing time is controlled by timer and can be set arbitrarily in the range of 1-9999 seconds. The lifting mechanism is composed of motor, belt reducer, lead screw and other components, which is used to realize the lifting of agitator. When feeding or discharging, the agitator rises to the highest position, while when mixing, the agitator drops to the lowest position. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Conduct experiments with confidence and clarity using this premium 100ml borosilicate glass beaker. This versatile laboratory essential boasts exceptional features that make it ideal for a variety of applications. Crafted for Performance: High-Quality Borosilicate Glass: Experience unparalleled clarity with this beaker's borosilicate glass construction. This robust material offers superior resistance to thermal shock, making it safe for use with heated or chilled solutions. Chemical Compatibility: Worry less about unwanted reactions. Borosilicate glass exhibits exceptional chemical resistance, ensuring the integrity of your solutions and the beaker itself during experiments. Designed for Versatility: Precise Measurements: Printed graduations on the beaker's side allow for accurate measurement of liquids up to 100ml. Estimate smaller volumes with ease thanks to the clear visibility provided by the borosilicate glass. Functional Design: The beaker's spout facilitates controlled pouring and minimizes spills. The stable, wide base ensures the beaker sits securely on your workbench.
Conduct experiments with confidence and clarity using this premium 250ml borosilicate glass beaker. This versatile laboratory essential boasts exceptional features that make it ideal for a variety of applications. Crafted for Performance: High-Quality Borosilicate Glass: Experience unparalleled clarity with this beaker's borosilicate glass construction. This robust material offers superior resistance to thermal shock, making it safe for use with heated or chilled solutions. Chemical Compatibility: Worry less about unwanted reactions. Borosilicate glass exhibits exceptional chemical resistance, ensuring the integrity of your solutions and the beaker itself during experiments. Designed for Versatility: Precise Measurements: Printed graduations on the beaker's side allow for accurate measurement of liquids up to 250ml. Estimate smaller volumes with ease thanks to the clear visibility provided by the borosilicate glass. Functional Design: The beaker's spout facilitates controlled pouring and minimizes spills. The stable, wide base ensures the beaker sits securely on your workbench.
Compliance With Following International Standards: AS PER BS 1881 PART 5: This apparatus is used to assess the surface absorption characteristics of concrete.The rate of flow of water per unit area into a concrete surface when subjected to a constant head of 200 mm is measured. The unit consists of a capillary tube mounted on a scale, a water reservoir & connecting tubes. Easy to use, mounted on a stand. As per BS 1881: Part 208:1996 Weight : 30 kg Approx. Further details available on our website. The Price mentioned here are subject to change as per the capacity, specifications and application of the user.
Our Laboratory Equipment Manufacturer produces top-of-the-line lab equipment exported globally for its precision and quality. From Kenya to the USA, our products excel in accuracy.
Enhance your concrete testing capabilities with our premium Concrete Cube Moulds. Manufactured with precision in Mumbai, India, these ISI standard moulds ensure accurate and reliable results every time.
Find the finest Most Accurate Woven Wire Mesh Sieves Supplier crafted to perfection for precise results. Compliant with international standards, our sieves ensure the utmost accuracy in various applications.
Globetrek's woven wire mesh sieves are essential for laboratory sampling and particle size analysis. Available in various diameter sizes and aperture ranges, these sieves are crafted from high-quality materials.
CE Approved and Doctors recommended Pregnancy Test. The most sensitive rapid pregnancy test for early pregnancy detection. 1.Product Description: Human Chorionic Gonadotropin (HCG) Test Kit (Colloidal Gold) is intended for the qualitative detection of human chorionic gonadotropin (HCG) in urine, which can be used for auxiliary diagnosis of early pregnancy. 2.Principle: The HCG Quantitative Test is a chromatographic immunoassay (CIA) for the detection of antigens to HCG in human urine or plasma/ serum. HCG-specific antibodies are precoated onto the membrane as a capture reagent on the test region. During the test, the specimen is allowed to react with the colloidal gold particles, which have been labeled with HCG-specific antibodies. Antigen to HCG, if pregnant, a red-colored band will develop on the membrane in proportion to the amount of HCG antigens presented in the specimen. .
Height Growth Maximizer is a natural supplement designed to support healthy height growth. Packed with essential nutrients and amino acids, it works to stimulate the release of growth hormones and improve bone density for maximum height potential. Height Growth Maximizer is a natural supplement designed to support healthy height growth. Packed with essential nutrients and amino acids, it works to stimulate the release of growth hormones and improve bone density for maximum height potential. Height Growth Maximizer is a natural supplement designed to support healthy height growth. Packed with essential nutrients and amino acids, it works to stimulate the release of growth hormones and improve bone density for maximum height potential.
INDICATOR SET (RH+LH)
Moisture Range 4%-30%Consistency +0.5%Commodity Calibration: Paddy, Bengal Gram, Wheat, Greengram and other grain seed. Principal of resistance: Resistance Handheld moisture tester easy and accurate. Alphanumeric LCD display. The equipment should moulded compression unit,
Pressure Transmitters Elevate your industrial processes with our precision-engineered pressure transmitters, meticulously crafted from high-grade metals sourced from India. Versatile Threading Options: Choose from a wide range of threading options, including ISO Metric, to seamlessly integrate with your existing systems. Tailored Specifications: Whether you require standard specifications or bespoke designs, our team of experts can create pressure transmitters that meet your precise requirements. Extensive Finishes and Coatings: Enhance durability and appearance with our diverse selection of finishes and coatings, including Natural, Nickel Plated, Tin Plated, and custom options as per your specifications. Our pressure transmitters are meticulously manufactured to ensure accuracy, reliability, and longevity. They are the ideal solution for demanding applications in industries such as process control, automation, and pneumatics.
CAPACITY : 6 Nos. INDENTER : 1.8mm FLAT TIP 6 Nos. WEIGHT : [A] 250g ± 1% - 6 Nos. made of Stainless Steel. [B] Additional Weight : 2.25 kg. ± 1% made of Stainless Steel –6 Nos. Complete with 6 Nos. Analog Dial Gauge duly calibrated with NABL Traceability.
“NOVA” CATHODIC DISBONDMENT TESTER – HMI TOUCH SCREEN MODEL Cathodic Disbondment is the loss of adhesion between a Cathodic coating and its metal substrate due to the Products of cathodic reaction (corrosion reaction) that take place in the interface of coatings. FEATURES: Use for inspection of Coating quality as per ISO 21809-1, DIN 30670, CAN/CSA Z245.20, [ASTM A775 / A775M-16 TEST METHOD ASTM G-8, ASTM G-95, ASTM G-80, ASTM G-42, EN 10290 ANNEX E, ISO 15711 (E), NF A 49-711 Standard.]……………………….. Note : With required additional accessories as per different standard – Quoted separately OR will be quoted as per requirement. Algorithm developed to maintain constant Voltage throughout the test. As per the standard – 8 hour test to 30 day test can be performed. Programmable timer built in for continuous process. All channels can run simultaneously as well as individually. Individual display and control Compact Electronic design Compatible with “NOVA” specially designed Sand Bath. [Available Optional]
Our Drop Weight Tear Testing Machine (DWTT) is engineered to assess the fracture characteristics and ductility of pipeline steels. Designed for rigorous testing, it complies with international standards such as API 5L3, ASTM E436, and EN 1027412. The DWTT machine features a robust construction to withstand high-energy impacts, ensuring reliable and accurate results. Equipped with advanced technology, it offers automated specimen loading and precise impact control. The machine can handle specimens with thicknesses ranging from 6mm to 60mm and impact energies up to 120kJ2. Key features include a guided mass system for consistent impact geometry, multiple long-stroke shock absorbers, and high-quality control software for data analysis. Ideal for industries requiring stringent material testing, our DWTT machine guarantees safety, efficiency, and superior performance. Trust our expertise for your critical testing needs and ensure the highest standards of material integrity.
Kaleidoscope Rotary Super Flower With Wooden Base, Beautiful Wedding Gift, Home Decor, Anniversary Gift. Amazing And Very Special Gift For Anyone :) Aluminum Made, Wooden Base Rotary Flowers Dial Antique finished Kaleidoscope Size Length: 9 Inches Rotary Dial Size: 4.25 Inches Wooden Base Size: 9X5 Inches Vintage looking Beautiful Decorative And Collectible Item For Gifting Purpose.
